SAN استوریج EMC

  • 0

SAN استوریج EMC

SAN استوریج EMC

استوریج های Block شرکت EMC به استوریج هایی که در شبکه SAN مورد استفاده قرار می گیرد اطلاق می شود.


  • 0

نصب کابلهای استوریج VNX5300 Unified و DAE ها

Shown in the upcoming figures (Figure 80 on page 94 and Figure 81 on page 96) are
graphical representations of SAS cabling in a DPE-based VNX storage platform, the
VNX5300 File. The Storage Processors connect to the DAEs with SAS cables. The cables
connect LCCs in the DAEs of a storage platform in a daisy-chain topology.
The DPE is automatically Enclosure 0 (EA0). The DAE connected to SAS output port 0 is
Enclosure 1 (EA1).
The first DAE connected to the Storage Processor SAS output port 1 is designated
Enclosure 0 (EA0). Each DAE connected after the first DAE increments the enclosure
number by one. All enclosures connected to SAS Port 0 will show an ID of 0.
Figure 80 on page 94 shows the first example of a VNX5300 File platform with two DAEs
(one 3U, 15 disk drive DAE and the other a 2U, 25 disk drive DAE) or a VNX5300 platform
with a total of from 55 disk drives (if the DPE is a 3U, 15 disk drive device) or 65 disk
drives (if the DPE is a 3U, 25 disk drive device).
The SAS ports on the VNX5300 platform 3U DPE are labeled 0 and 1. SAS 0 is connected
internally to the SAS expander that connects the internal DPE disks. Since SAS 0 is
already connected internally to the DPE disks, the first DAE is connected to SAS 1 to
balance the load on the SAS ports. The second DAE is connected to SAS 0, the third DAE is
connected to SAS 1, and so on.
In Figure 80 on page 94, notice that each DAE device supports two completely redundant
buses (LCC A and LCC B).
The rule of load or bus balancing is applied to all DAEs. That is, Bus 0 is Enclosure
Address 0 (EA0), Bus 1 is EA0, and so on. In the case of the VNX5300 platform, Bus 0 EA0
is the DPE (SP A and B). So, to balance the load, Bus 1 EA0 becomes the first DAE (LCC A
and B) in the cabinet with the next DAE (LCC A and LCC B) as Bus 0 EA1, and so on. If you
have several DAEs in your VNX5300 platform, you can daisy chain them within that
particular bus. However, it is recommended that you balance each bus. In other words,
always optimize your environment by using every available bus, and spreading the
number of enclosures as evenly as possible across the buses.
Note: On the DPE and DAE, each cable connector includes a symbol to denote the
direction the cable needs to connect to. The cable connector that has a double circle
symbol is the input to the device. The cable connector with the double diamond
symbol is the output from the device.
IMPORTANT
Notice the description of the cable labels affixed to the SP to DAE cables.

The cables shown in Figure 81 are:
Note: The cable colors shown in the example are orange for Bus 0 and blue for Bus 1.
◆ Cable 1, blue, DPE to 1st DAE (labels SP A SAS 1 to LCC A)
◆ Cable 2, blue, DPE to 1st DAE (labels SP B SAS 1 to LCC B)
◆ Cable 3, orange, DPE to 2nd DAE (labels SP A SAS 0 to LCC A)
◆ Cable 4, orange, DPE to 2nd DAE (labels SP B SAS 0 to LCC B)

Cabling-with-two-DAEs-in-a-VNX5300-File-Unified-platform-نحوه-نصب-استوریج


تفاوتهای DAE و DPE در استوریجهای EMC VNX

emc-vnx-DAE-DPE-استوریج

در این مطلب می خواهیم در خصوص مفاهیم و ساختارها و کامپوننت های مربوط به استوریج های EMC سری VNX/VNXe بحث کنیم.

شاسی های ارائه شده توسط کمپانی EMC معمولا در سه دسته DAE و DPE و SPE می باشند که هر کدام کاربرد بخصوص خود را دارند.

در شکل زیر می توانید ساختار کلی رک EMC را ببینید.

EMC-VNX-5200-5400-5600-5300-فروش-استوریج-قیمت-استوریج

DAE

DAE که مخفف Disk Array Enclosure می باشد کامپوننتی از رک EMC شما می باشد که محل قرار گیری دیسکهای فیزیکی ما که جهت ذخیره سازی داده ها از آنها استفاده می کنیم می باشد. این محفظه های و یا همان Enclosure ها معمولا در شکل ها و اندازه های متفاوتی ارائه می شوند که با توجه به نیاز شما انتخاب می شود.

Enclosure ها در دو مدل کلی مخصوص هاردهای 2.5 اینچی و مخصوص هاردهای 3.5 اینچی تولید می شوند.

DPE

DPE مخفف Disk Processor Enclosure می باشد. DPE کلیه قطعات کاربردی استوریج EMC و یا در واقع کلیه چیزهایی که با پروتکل Block در ارتباط هستند را شامل می شوند. این شاسی همچنین مکان قرار گیری دیسک درایو های Vault نیز می باشد. نرم افزار OE که عنوان سیستم عامل استوریج های بلاک (Block) مورد استفاده قرار می گیرد بر روی والت درایورها (Vault) نصب و تحویل مشتری داده می شود.

SPE

SPE مخفف Storage Processor Enclosure می باشد که بطور معمول در سیستم های استوریج بسیار بزرگ شرکت EMC مشاهده می گردد. این SPE ها بر روی شاسی های قرار می گیرند و شامل پردازنده هایی برای انجام عملیات عمومی سیستمی می باشند.

SPS

Storage Processor بیشتر عملیات مربوط به سیستم عامل دستگاه EMC را انجام می دهد این عملیات شامل نوشتن و بازیابی کردن دیتا ، عملیات RAID و Read/Write Caching می باشند.

Ultraflex I/O Modules

کارتهای PCIe که معمولا بر روی سیستم استوریج های EMC VNX مورد استفاده قرار می گیرند. اسلات های مخصوص کارتهای IO بر روی دستگاه DPE نصب و برای ارتباط با Storage Processor ها و Data Mover های دیگر مورد استفاده قرار می گیرد.

Data Movers and Blades

Data Mover ها که به آنها X-Blade نیز گفته می شود دسترسی فایل را به کاربران از طریق Storage Processor سیستم استوریج EMC میسر می سازد. این دستگاه ها بر پایه سیستم لینوکس بوده و از هارهای SCSI استفاده می کند.

Data Mover ها و Enclosure های X-Blade بر روی سیستم های EMC VNXe3200 ارائه نمی شوند بلکه سیستم خود سخت افزار لازم را برای این منظور بر روی دستگاه تعبیه کرده است.

CS

Control Station ها وظیفه مدیریت کامپوننت های مربوط به File و Unified بر روی دستگاههای VNX را بر عهده دارند.

نکته قابل توجه این است که دستگاههای Block مانند VNXe3200 از هیچ CS استفاده نمی کنند.

NAS

NAS که مخفف Network-Attached Storage می باشد به عنوان استوریج به اشتراک گذاشته شده سرویسهای فایل سیستم و استوریج را برای سرورها انجام می دهد.تمامی سیستم ها از طریق آدرس IP به اشتراک گذاشته شده به سیستم وصل می شوند و از فایلهای موجود بر روی این استوریج استفاده می کنند.

 راهکار های نوین ذخیره سازی و بکاپ EMC را از ما بخواهید.

شماره تماس: 88884268


آخرین دیدگاه‌ها

    دسته‌ها